Gasia Usb Keyboard Driver Download

• Hi !

  Pi Model:2 B
  RetroPie Version Used: 3.2
  Built From: SD Image
  Guide used: wiki
  USB Devices connected:
  Bus 001 Device 005: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode)
  Controller used: Gasia Co.,Ltd PS(R) Gamepad
  Bus 001 Device 006: ID 054c:0268 Sony Corp. Batoh Device / PlayStation 3 Controller

  Error messages received: none
  pi@retropie ~ $ hcitool scan
  Scanning …
  pi@retropie ~ $ hcitool dev
  Devices:
  hci0 00:11:F6:0B:28:9E

  how to configure this gamepad ???

  thank you for your help !

  M@rco

  Looks like a PS3 controller clone!? Try to install ps3controller module. And if it is working please post your controller config files (/opt/retropie/configs/all/retroarch-joypads).

  Having the same issue, works fine wired. And if I press the ps button on any genuine Ps3 controller it pairs fine and works but the clone just flash’s until it stops with no sync and then have to restart the unit to use the controller wired again.

  There is an qtsixad package with gasia support on github. Default qtsixad does not seem to work with gasia clones.
  https://github.com/falkTX/qtsixa

  Just out of interest. Where can i buy this ps3 controller clone?

  Can purchase them on ebay mate.

  How do we go about installing that package.sorry very new to this stuff.

  Thanks for quick response and help.

  Bump… Good question my local market is flooed witn these clones would be good to see how to fix?

  Sent from my LG-D855 using Tapatalk

  I will post something if it is running.

  [quote=109666]I will post something if it is running.

  [/quote]

  Please do, still can’t get it to work and not sure how to use the install the above method.

  You can try this ps3controller module:
  https://github.com/gizmo98/RetroPie-Setup/blob/ps3-gasia-hack/scriptmodules/supplementary/ps3controller.sh

  Or type…

  …and (re)install ps3controller

  I just gave that a go but after typing git clone etc. It said cloning into ‘retropie-setup’ then asks for user name and password? Which I do not have ? so it started to work lol

  Ok sorted it out but still no go.thanks anyways.

  yes – two posts up.

  @slayer
  My fault. You need to checkout another branch. Please try…

  [quote=110198] @slayer
  My fault. You need to checkout another branch. Please try…

  [/quote]

  Champion,I did all that and didn’t think it worked, when I unplugged the control then pressed the p3 button it flashed all four lights fast and then went to a slower flash and just kept flashing then I tried the controls and they work perfectly,not sure how two controls will go but shouldn’t be too much of an issue hopefully, thanks heaps for the help mate.

  Good to here it is running! Gasia hack + led support is broken at the moment and i don’t know if it can be fixed.

  [quote=110268]Good to here it is running! Gasia hack + led support is broken at the moment and i don’t know if it can be fixed.

  [/quote]

  Even if it can’t that’d fine as long as it works I don’t need the LED lights to tell me what player I am ☺ thanks again for helping us out with this issue.

  That’s what I did install/pair then it will do its thing and come up with a message saying to connect controller via usb etc etc hit ok, restart and load into ES then disconnect cable and press p3 button wait few seconds and it should be ok, if not go to menu and configure control and it should say 1 gameplay detected then press and hold p3 button ☺

  Remove configs/driver (no.2) before you install.

  When in ES and you disconnect the usb and press the p3 button what do the lights do on the controller?

  I had that happen too,but it was a fast flash for a few seconds then it slowed down, once that happened I was able to configure input in ES menu as it detects a new controller.

  @mrco123
  Could you test something for me? Remove your rc.local changes. Update RetroPie-Setup and reinstall PS3 controller driver with “clone support”.

  Thanks! The next sd card image will have a install option for clones.

  Sorry i don’t know how to solve this problem at the moment. If you have only one controller enable safety.timeout: “/var/lib/sixad/profiles/default” “enable_safety_timeout 1”

• Posts

• The forum ‘Controller Configuration in RetroPie’ is closed to new topics and replies.

Gasia Ps3 Controller Driver Windows 7 Update; Gasia Ps3 Controller Driver Windows 7 Download; Please read all instructions carefully. Not all devices are supported, therefore it is strongly recommended that you try the Sixaxis Compatibility Checker.

Gasia Usb Keyboard Driver Android

1. The steps to get your PS3 controller working with your PC are very easy, we won't be using MotionJoy in this tutorial, we will be using XInput Wrapper for DS3 (SCP DS3 driver). This guide will work for any original PS3 DualShock 3 controller, and fake/knockoff cheap Oshodi DualShock controller to work.
2. I've a Gasia controller, plugged in - lsusb reports it as a 'Sony Playstation' controller, but something like evtest reports it as 'Gasia Co.,Ltd PS(R) Gamepad' - which is what it is. I got mine working by bluetooth by ensuring I only had the right option (PS3 controller/clone support gasia/gasia only/clone support shanwan).